Showing posts with label Caribbean sailing. Show all posts
Showing posts with label Caribbean sailing. Show all posts

01 March 2020

Back in the US, Sort Of

Argon has been been easing her way out of the deep Caribbean in to more American-feeling territory ever since about St. Martin with its commerce and infrastructure as well as Anguilla accepting US dollars and completely English-speaking. We were welcomed back home with the ease of clearing customs in US territory upon arriving in St. Croix as well as the plethora of Americans inhabiting St. John (both US Virgin Islands). It feels as though we may have swapped exotic adventure for comfortable familiarity at these latitudes. But it's still grand.

Captain Linda Perry Riera

Argon sailed and explored about 160nm in total over the past two plus weeks from Anguilla to St. Croix (USVI) then on to and around St. John (also USVI).

A difficult downwind overnight passage from Anguilla to St. Croix USVI was followed by a grand daysail due north to St. John (also USVI, just southwest of British VI).


Overnight Sail from Anguilla to St. Croix, With Crew

Anguilla is a narrow island a mere 5 miles north of St. Martin. Its topography is nondescript but with gorgeous waters. Locals seem happy to be largely overlooked by their bustling neighboring island with just enough high end tourism to keep the economy healthy. Anguilla seems to have the most mixing of races we've seen in the Caribbean perhaps due to what appears to be an overall higher standard of living for locals compared to other islands where there is a clear divide between locals and ex-pats. The locals were among the friendliest we have encountered in our travels.

After a week at anchor working day jobs, tending to boat logistics and a bit of land exploration we welcomed our dear friends, Lori and Colonel Todd, to Anguilla to celebrate their impending retirement from nearly 30 years in the Marine Corps. Lori and Todd started sailing in Newport a few years ago and were keen to get some experience in big waters, on a larger boat, and to experience the cruising lifestyle.

An overnight westward passage would be a downwind sail in 15-18kt winds. Seas proved to be the most challenging factor with confused 4-8 foot waves bashing our stern quarter requiring constant helm attention and resulting in uncomfortable motion of the boat the majority of the 100nm sixteen hour overnight passage. We had to stay off the wind more than we would have if the seas were calm requiring us to jib a few times and add some miles to the rhumb line. The sea state finally became more rhythmic and comfortable around daybreak as we welcomed the view of St. Croix.

After a week of work and boat logistics, we welcomed dear friends to Anguilla.


Preparing for the 100nm overnight sail from Road Bay, Anguilla to Christensted, St. Croix.


Ready for an evening departure from the windy anchorage at Road Bay, Anguilla.


Lori practicing helming and getting used to the feel of Argon in the lee of Anguilla before dark sets in and seas roughen. (They were both happier than they appear in this photo.) We were mostly double-reefed with just the 90% jib which enabled us to maintain 6.5-7.5kts.


The morning after... A challenging, successful night sail was celebrated with strong coffee as seas calm on the approach to St. Croix.

Christiansted, St. Croix - USVI

Americans clearing in to customs upon returning to the US have the option of using the new Roam App. A bit of time was spent a week prior setting up the account and profiles for about a $30 fee. When in St. Croix, I simply logged our arrival when anchored and waited about 30 minutes to receive an acknowledgement from Customs and Boarder Patrol (CBP) and permission to be back in the US. So convenient! I will try using this again when we leave US territory and return again.

We quickly loved the town of Christiansted with a myriad of beautiful buildings and interesting side streets and art galleries. However, it is not an ideal cruiser's destinantion. The anchoring options are limited and we had an extremely rolly night (but with good holding) after being asked to leave our first anchoring spot. After making our way to an antiquated fuel dock in high winds the next morning to top off diesel and water, we were introduced to the pervasive friendliness of Christiansted. Miracle was a joy to chat with and one of the boat yard workers kindly offered us his mooring in a much more protected and comfortable part of the harbor. Thus after a rough initial introduction, Argon and crew were able to settle in and enjoy the pearls of Christiansted.


Very uncomfortable and rolly anchorage a long dinghy ride from town.


Mircacle, from St. Croix Marina, was a gem. She got us connected with a co-worker who offered up his mooring to us.

On day 2 we were able to get a great mooring behind a tiny island in crystal clear water and a very easy dinghy ride to town. There are ample tie ups for dinghies along the boardwalk but a stern anchor is advisable to prevent the tender from constantly bashing in to or under the docks.


Bob installed this cleat to the transom of the dinghy which facilitated securing the stern anchor rode.


A little bit of partying and celebrating in St. Croix at BES Craft Cocktail Lounge.


Downtown Christiansted, St. Croix.


St. John - USVI

After three nights in St. Croix we released the mooring lines at 0900 for a 35nm close reach sail in 14kts, reasonable seas, with full main and jib landing in a lovely southern bay of St. John by early afternoon. It was great to arrive to a new island and not have to bother with customs (since we were already cleared in to US via St. Croix).


St. John is on my list of top 5 favorite Caribbean places to sail. The numerous gorgeous bays and concise circumference of the island enable one to find a lovely cove to tuck in regardless of the conditions. With a majority of its 20 square miles national park there are numerous hiking options. We enjoyed the following harbors on this trip:
  • Little Lameshur
  • Rendezvous Bay
  • Waterlemon Bay
  • Francis and Maho Bays
  • Lindt Point, Caneel Bay and Cruz Bay
The National Park Service (NPS) maintains moorings requesting $26/night in park waters comprising much of the south and north coasts. While this can add up and impact ones cruising budget, it is well worth it as the moorings are excellent quality and the prohibition of anchoring contribute significantly to the quality of the harbors by protecting the sea beds. Recently slashed NPS funding  in addition to recovery from the devastating hurricane Irma in fall of 2017 is negatively impacting NPS activties including enforcement of fee collection (which will eventually lead to less funds for mooring and trail maintenance). Let's hope that funding and associated activities are restored soon.

More than a week was spent jumping from one harbor to the next around St. John. Favorites are the coves on the less traveled south coast especially Little Lameshur and Rendezvous Bays.


Lori and Todd sailing with us on a close reach from St. Croix to St. John - much more favorable conditions compared to the overnight passage a few days prior.


Argon spent several days in Little Lameshur, sometimes alone. This view is from Yawzi Point, one of the several hiking trails surrounding this cove.

St. John was ideal for regular exercise swims. One morning in Little Lameshur a large barracuda was hanging out around the boat (they seem to enjoy the shadow of the hull). It took me a while to muster up the nerve to gently slide in the water and start my swim. Barracuda are common and not overtly aggressive but they have enormous sharp teeth and one does not want to inadvertently startle a barrack in to attack mode.



Fun impromptu meet up at Francis Bay with a former sailing instructor (Brenton of Blackrock Sailing School) and his current class on their Foutaine Pajot 40 catamaran. A big surprise was that one of the students is a work colleague of Bob's - small world.

Johnny Horn Trail.



Argon moored in Waterlemon Bay.

Eating Aboard

With all the secluded harbors, we were happily eating aboard quite a bit. Although the last provisioning run was only about a week ago in St. Croix, our stores were getting lean. We were still able to muster up some satisfying meals as the cabinet and refrigerator became sparse. Finding fresh vegetables and good quality meats is a challenge along many of the Caribbean islands. Cooking with various types of legumes has become commonplace. Canned mushrooms are a regular in my cooking as good quality fresh mushrooms are non-existent. Cabbage is wonderful for its shelf life and versatility including using in place of lettuce which is difficult to find fresh and does not keep for long. Weak fishing skills prohibit us from relying on fresh fish but we keep going at it.

Crispy tofu with spice Thai noodles.


Braised beef with polenta.

Beef and bean burritos made with Impossible Beef (plant based meat product).


Scrambled eggs and sauteed potatoes with paprika and brie cheese.


What About St. Thomas? And the BVI?

We have enjoyed the lovely profiles of the lively and bustling British Virgin Islands and St. Thomas in the near distance of St. John but have decided to by-pass these popluar island in exchange for more time in the quiet coves of St. John. We will soon set sail westward for the Spanish Virgin Islands (also US territory) first stopping at the secluded island of Vieques.



View from one of the many spectacular hikes on St. John. This one from atop Lienster Point with Tortola and Little Thatch (part of the BVI) in the background.




16 February 2020

More Boat Projects in Paradise

After an indulgent extended weekend in Saba, attention was quickly re-focused on Argon. We had a few more days tied to a dock at Simpson Bay Marina on the dutch side of St. Martin thus a perfect time to tackle our latest nautical to do list.

Captain Linda Perry Riera


Back to Cruising Life - More Boat Projects in Paradise

Just few weeks ago we were feeling accomplished when numerous projects and chores where completed while docked at Nelson's Dockyard, English Harbor. But alas, the new list started to form even before we left Antigua.

Topping Lift

The topping lift runs from the top of the mast to the aft end of the boom. Most of the time it hangs a bit slack and does nothing. Sometimes, such as when motoring in sloshing seas, the topping lift is important for holding the boom up off the bimini and dodger. Recently (ever since bending the new main sail in Grenada) the topping lift has caused us trouble periodically by fouling in the leech cleat, batten pockets or reefing rings causing angst and mild terror when struggling to drop the sail including once when approaching dangerous reefs in Barbuda. The assessment, options and solution will be a topic of a separate blog coming soon.

The topping lift has been causing problems - getting caught in the leech cleat, Antal rings (for reefing) and the batten pockets. This has been quite frustrating and a bit scary when it interferes with getting the sail down. Bob has been thinking a lot about options. A detailed sailing geek blog dedicated to the topping lift is forthcoming.


Getting ready to be hoisted up the mast to check out the topping lift and re-run the lazy jacks.


View from just above the first set of spreaders to re-run the lazy jacks. Also removed the connection of the topping lift at the top of the mast

Boom Pad Eye and Backing Plate

It's just a little pad eye... what's the big deal?

We were awoken suddenly in the early morning dark while anchored near St. George, Grenada, back in November to a crash and loud rhythmic squeaking as the boom thrashed back and forth violently, its inertia accentuating the sounds in the swell. The dock line that runs from under the boom, normally attached snugly to a midships cleat to keep the boom stable and quiet while at anchor, lay slack. Quickly we found the culprit - a busted pad eye. This pad eye also attaches the boom brake (which made the crashing sound when falling on to the deck). @#$%! We re-fasten the boom temporarily and commited to making a more complete assessment at day light.

Argon's boom is a carbon fiber pocket style. Inside the V of the boom is a flat base allowing for a long hollow chamber for the out haul and reefing lines to run through in addition to the backing plates for the head of the vang and several pad eyes with backing plates to attach various blocks and run lines. After considering options, we decided to move an existing extra pad eye to the recently opened hole. That extra pad eye is normally the attachment for the Wichard Boom Brake. We knew we had mostly upwind sailing in the near future until at least Antigua so this wasn't that urgent as the boom brake is more instrumental when sailing down wind. We planned to fully address the busted pad eye situation in Antigua a few weeks ago, but our time at dock there was during an especially windy spell which prevented us from doing anything that required removing the boom from the mast. But now that we are in St. Martin at a dock with low winds, with more down wind sailing for the next few months, it is time to get this fixed appropriately.



Back in November (Grenada) a pad eye under the boom busted (strangely, while we were at anchor). Now that we are in the cruiser's shopping mall of the Caribbean and on a dock, it is time to get this fixed properly.

Main sail taken off on a low wind morning in preparation to try to get the busted backing plate out of the boom. Good time to also inspect the sail track cars and replace any missing ball bearings. We wanted to use the broken backing plate as a template to get a new one fabricated and remove it to prevent it from perhaps fouling something someday.


First, let's retrieve the broken backing plate from the boom by tilting the boom up...


Ok, tilt it more; shake it around. Nothing. No sign of the backing plate.

Let's try removing the boom completely and hanging it vertical. (What can go wrong?) Ugh - still no backing plate! Bob said it must have gone in to another dimension.

Ok, now dinghy across the lagoon over to FKG Rigging to get a new pad eye and backing plate fabricated (and a spare). $200 and a couple days later - voila!

New pad eye and backing plate; and a spare.


Messenger line attached for the patience-testing activity of getting the new pad eye through the boom, pulled in to the slot in the carbon, and re-fastened.


After several tries and permutations with messenger lines and a metal hook...

Almost... now to get those fasteners in.



FKG did a very nice job fabricating the new backing plates without one to use as a template, but the threaded holes were just a tiny bit off center of the clearance holes in the carbon.  We opened two of them up just a bit.


Ta-da!!! Phew, that was quite the project. Now time to get the main sail back on.

Dinghy Scrubbing

Algae and barnacle growth on the bottom of Argon as well as the dinghy requires regular attention. Argon has ablative anti-fouling bottom paint which helps control the growth but still requires us (and occasionally a professional diver) to scrub and scrape. The growth on the aluminum dinghy bottom and hypalon inflated pontoons is particularly stubborn. I have been unable to get the dinghy bottom clean with a scrub brush while she has been in the water. This is going to require a more concerted effort and chemicals.

Dinghy bottom before: The stubborn algae was impossible to scrub off with a stiff brush in the water. Time for more concerted effort (and chemicals).

The outboard, bench, and all contents removed; dinghy hauled up on to the dock, Calbert and I attack the dinghy with diluted On-Off, Simple Green, Magic Eraser, regular boat soap and elbow grease.

After:  Much better! We are now going to be more disciplined about hoisting the dinghy on the davits more often when not in use to keep the growth at bay.

Hull & Deck Waxing, Stainless Polishing, Teak Cleaning

The salt and sun wage constant assault on a boat. I set my sights on polishing the stainless steel, waxing the gel coat decks, and cleaning the teach cockpit. Help is employed to clean and wax Argon's hull.


I splurge and hire Calbert and Pete to clean and wax Argon's hull while I work on the waxing, polishing and other cleaning.

Some of the products used to help keep Argon shiny:  Scotch Guard and 3M for waxing the hull and gel coat. And some Awlgrip wax (not pictured) for a finishing touch on the hull. Flitz for polishing the stainless steel along with OsPho and Spotless Stainless for the more stubborn rust spots.

Cockpit teak scrubbing.


Deck waxing started in St. Martin and finished while at anchor in Anguilla. Well, is it ever finished?


Water Treatment, Tank Filling, Strainer Cleaning and Laundry

Argon carries 135 gallons of water between two tanks. We have no water maker nor a sophisticated water treatment system. To keep the tank water potable, we flush the tanks periodically (difficult with scarcity and expense of good water in the Caribbean) and the add chlorine. When there is enough fresh water to spare, I can do some laundry by hand. Raw water filters for the refrigerator, diesel and air conditioner are checked and cleaned regularly.

Water tanks were low so we decided to give them a good shock with some extra bleach while we were away in Saba. Then inspect to ensure all looked fairly clean and clear, followed by a good flushing. Having access to good potable water at the marina (at 20 cents / gallon!) allowed us to have full water tanks upon departure. We can last up to 3 weeks with very careful usage.

Good time to check the refrigerator and diesel raw water strainers. In addition to needing a cleaning, this one is getting corroded and will soon be replaced.
 
Several loads of laundry were done at a nearby laundromat but some items were best hand washed on board.

Jib Furling Drum Repair

The Harken furling systems are mostly very well designed. The weak spot is the top and bottom platters inside the drum. They consist of semi-circles of plastic held together by two fasteners. The problem is that the attachment for these fasteners breaks over time. More than a year ago in Bermuda, Bob did a "hack" to hold the platters together after this breakage. The problem if they separate is that they can no longer spin freely inside the drum. And spinning freely is the main thing a furling system is supposed to do.

While sailing from the dutch to the french side of St. Martin, we noticed that the jib was getting difficult to furl (again) and upon inspection, the Bermuda hack had failed and the bottom platter had separated. It was time to re-hack it. Always the engineer, Bob was saying something about a re-design and buying a 3D printer when we get home.



After departing Simpson Bay Marina en route to Marigot on the french side of St. Martin, we realized that the jib furler had an issue. Luckily Bob was able to fix it at anchor without taking down the jib as the winds were up.

WiFi Router - Failed Attempt to Resuscitate

Our beloved ArgonAfloat network is served by a Ubiquity Bullet Titanium router mounted up on the radar mast. The router has been getting flaky over the last few months sometimes working great, other times not so much. Normally cleaning connections and chanting incantations has solved the issue, but now it seems, the Bullet itself is really dead. Bob unmounted it from the mast and did some testing down below and declared "He's dead, Jim". It's been baking in the sun and freezing in the winter for five years, so we don't feel too badly about it. Fortunately, we are at a point in the cruise where we can primarily rely on mobile data from here on out anyway. We're shopping for replacement solutions (maybe another Bullet), but won't buy anything until we are stateside again.



Resuscitation of the WiFi router failed.

Vented Loop and Engine Check

The sump has been periodically kicking in even when no water is being flushed down its drains. If no water is flowing in to the sump, the only other source is that the discharge is siphoning back. A couple years ago, we added a vented loop to the sump discharge which solved the issue until recently. While in St. Martin we purchased a new vented loop and a spare. Time to crawl in to the aft bowls of Argon and replace. And, while back there, we also opened up the access panels to the starboard side of the diesel for an inspection revealing a broken air intake filter laying on the floor of the engine room. The foam was pretty much disintegrated. Another item to write on the shopping list (and we'll get a spare of course). In the meantime, we fabricate a new temporary one.

After clearing out the aft cabin (that functions as our storage closet for all sorts of stuff) Bob crawls back behind the cabin to replace the vented loop for the sump.


Upon peering in to the engine compartment I see the air filter has broken off.


We decide to sacrifice a linen top of mine to make a new air filter.


Jerry-rigged air filter. And one less white top.

Fishing and Sailing

Although maintenance and repairs are continual, and demands of our day jobs are constant, we feel pretty caught up and will be able to spend more time sailing and exploring for the next week or so.

Experimentation with different fishing lures continue as we troll between islands with recent activity. And we eagerly await the arrival of dear friends as we round out our stay in Anguilla.


Switching up lures off the coast of St. Martin.

Landed and carefully released modest sized barracuda.


First time using a simple cedar plug en route to Anguilla catches this marlin but only after his hind third was chomped by a shark or some other big fish. I was able to fillet a fair amount of delicious meat off the remaining part.



My office while at anchor in Road Bay, Anguilla.


Bob's office for a bit at Sunshine Shack, Rendezvous Bay, Anguilla.



Johno's, Road Bay Anguilla.


Our neighborhood for a little more than a week - Road Bay, Anguilla.

Even time for some music making now.